Eton VECTOR 250R User Manual Page 14
- Page / 32
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Page 13
Changing the engine oil
The engine oil requires changing every
1800Mi / 3000KM and at the start of each
riding season to protect the engine.
The following steps should be followed
when changing the engine oil.
1. Place a oil catch pan directly below
the engine crankcase.
2. Remove the crankcase drain plug
located on the bottom of the crankcase
on the underside of the unit.
3. Remove the engine oil dipstick
located on the right hand side of the
crankcase directly below the
transmission shift lever.
4. Allow the oil to drain completely (15-
30min).
5. Reinstall the crankcase drain plug
and torque to 7-10lb-ft.
6. Fill the crankcase with SAE10W-30
automotive grade engine oil through the
dipstick hole. 1.2 liters / 1.2 quarts.
7. Reinstall the engine oil dipstick and
finger tighten
8. Dispose of used oil at a proper
recycling station as required by law.
Engine Cooling System
The Vector engine is a liquid jacketed cooled
engine. Cooling is accomplished by
circulating liquid coolant from the engine coolant
jacket through a radiator located at the front of
the unit. If is very important to keep the radiator
fins clean and free of debris and mud to prevent
engine overheating which can cause engine
damage or failure. You need to routinely clean
the radiator by using a pressurized spray of water.
Maintaining the coolant level is also a very
important process to ensure proper engine
cooling. The coolant level should be checked
before each riding session and the coolant
replaced at the beginning of each riding season.
Proper maintenance of the cooling system will
prevent the engine from overheating and freezing.
Coolant should be change every 2 years.
Checking the level
With the unit parked on level ground, remove the
front grill cover and check that the coolant level
in the reserve tank is between the upper and
lower limit indicator lines. If the coolant level is
near or below the lower limit add coolant to raise
the coolant level to the upper limit indicator line.
Coolant should be a mixture of distilled water
and anti-freeze.
CAUTION: Add coolant through the reserve
tank. The coolant system runs under pressure.
- Vector 250R 1
- OWNER’S MANUAL 1
- Table of Contents 3
- Safety Notes 5
- Additional safety tips: 8
- Engine Stop Switch 10
- Manual choke lever 10
- Throttle lever 10
- Control Features 10
- Front and Rear Brakes 11
- Parking Brake 11
- Fuel Tank 11
- Fuel Valve 12
- Inline Fuel Filter 12
- Engine Oil 13
- Oil Level Warning indicator 13
- Changing the engine oil 14
- Engine Cooling System 14
- Checking the level 14
- Engine Coolant Mixture 15
- Coolant system leaks 15
- Transmission 15
- Shifting gears 15
- Transmission Oil 16
- Tires and Wheel inspection 16
- Tire Pressure 17
- Spark Plug 17
- Spark Arrestor Screen 17
- Air Filter 17
- To clean the filter 18
- Braking Systems 18
- Rear Brake System Inspection 19
- To Fill the Reservoir 20
- Purging Brake Lines 20
- Drive Chain 21
- Throttle Lever 21
- Electrical Battery 22
- Digital Console 23
- ATV Break In procedures 23
- Pre-Operation Inspection 23
- Starting Procedure 23
- Driving your ATV 24
- Turning your ATV 24
- Parking Your ATV 24
- *subject to availability 26
- Page 27 28
- Vector 250R Wire diagram 28
- ETON AMERICA, LLC 29
- Owner’s Notes: 31
- Page 31 32
Powerplus POWXG4060 LEAF BLOWER 25CC DE podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Sprzęt ogrodniczy Powerplus POWXG4060 LEAF BLOWER 25CC DE.
Dostarczamy 1 pdf podręczników Powerplus POWXG4060 LEAF BLOWER 25CC DE do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Comments to this Manuals